. JI1FGX/DU9 Philippines Mindanao Diary JTDX Automatic Operation Software Ver0.4.0 (2025/04/19)
JI1FGX/DU9 Amateur Radio Diary, Mindanao, Philippines, IOTA OC-130.
English. Japanese.



Yesterday's access.
Introduction. [Lily Diary.】
A diary of life in Mindanao.

   
25/07/13  IARU HF Contest
25/07/10 Software updates
25/07/08 DXV500ZS linear amplifier repair
25/07/07 CQ Machine Program
25/06/21 LoTW system upgrade
25/06/18 RG8 for 3.5MHz arrived
25/06/15  Time setting Ver0.5
25/06/14 Drone Habsan ZINO arrives
25/06/12 Philippine Independence Day
25/06/11 Algeria 7X2RF QSL card.
25/06/10 Translation API Program
25/06/09 DXCC150 award certificate arrived
25/06/08 AutoCWType_Ver1.4.1
25/06/07 Introducing the Shack
25/06/06 A portrait drawn by ChatGPT.
25/05/26 Windows full-width/half-width switching.
25/05/17 OK2ZAW BCD to 16 converter.
25/05/16 For 3.5MHz Zepp antenna.
Stepping motors
25/05/15 3.5MHz stepping motor design.
25/05/14 3.5MHz tuning coil installed.
25/05/11 3.5MHz antenna installation completed.
25/05/03 JTDX Autonomous Driving Program Ver0.4.3.
25/04/26 Drone Habsan ZINO.
25/04/25 Time setting Ver0.3.
25/04/24 AutoCWType_Ver1.3.
25/04/23 Preparing for FTDX3000 LCD repair.
25/04/22 Installation plan for 3.5MHz Zepp antenna.
25/04/21 AutoCWType_Ver1.1.
25/04/20 10,14MHz antenna installation completed.
25/04/19 JTDX Autonomous Driving Program Ver0.4.1.
25/04/19 14MHz antenna pole installed.
25/04/18 ThinkPad X390 repair completed.
25/04/17 Search is now possible.
25/04/15 Preparing the 10MHz dipole.
25/04/12 Hexbeam Part8.
25/04/06 My ThinkPad X390 is broken.
25/04/05. Time setting program.
25/03/31 JTDX Autonomous Driving Program.
25/03/30 Automatic log sending from CWType to Hamlog.
25/03/21 Hexbeam Part 7.
25/03/20 FreeDV Part 3 First QSO.
25/03/18 FreeDV Part 2 QSO in the shack.
25/03/16 Hexbeam Part 6.
25/03/15 Install FreeDV Part1.
25/03/09 Hexbeam Part5.
25/03/07 Hexbeam Part 4.
25/03/05 28MHz antenna modification
25/03/01 FTDX3000 is broken!
25/02/28 Pileup at 50MHz FT8.
25/02/28 DXV500ZS linear amplifier repair.
25/02/27 Tower pipe rebuilding plan.
25/02/26 Direction to Japan from Ozamiz.
25/02/26 28MHz is not available.
25/02/23 DXV500ZS linear amplifier repair.
25/02/22 Hexbeam Part 3
25/02/21 Hexbeam Part 2
25/02/18 28MHz antenna construction.
25/02/17 18,24MHz antenna height construction.
25/02/16 Z26NS Cosovo.
25/02/14 21MHz FT8
25/02/12 7,21MHz antenna repair.
25/02/08 Operating CW at 21MHz.
25/02/05 DXV500ZS linear amplifier failure.
25/01/19 Input Director.
25/01/14 Temporary license renewal.
.
JTDX automatic operation software Ver0.4.0 (2025/04/19)
 
JTDX's automatic operation program has been upgraded.
1) Previously, I had to install the AutoHotKey program to get it to work.
Can now run independently as an EXE file
2) Button coordinates in the JTDX screen can now be entered in the "Settings" GUI.
(3) Easy installation with the installer attached.

JTDX_Automatic_Operation.v0.4.0.exe and JTDXAutomatic_Operation_Setup.exe are the programs

operation
 
" on the JTDX.Transmission startAfter clicking on the "+" button, if the timeout occurs, click on the "+" button again.Transmission startPress "+" automatically.
When it times out by calling another station or retrying during communication, it automatically "Clear DXPress "+" and then "-".Transmission startPress the "+" button.
When the logging window opens after sending RR73 with a successful QSO, it says "OKPress "+" automatically.

This program does only these three things.

JTDX automatic operation.Ver0.4.0.zip

Download count: 1 8_
 Warning.
Some awards prohibit automatic operation.
Development is only intended to assist operation in front of the computer, not for unattended operation
Please make sure to operate in accordance with the radio laws of your country.
I don't think it's a problem in Japan, since TNC had a 24-hour unmanned operation in Japan.
I, as the producer, will not be held responsible for any problems.
Use at your own risk.
The program isAutohotkeyThe script is programmed in the form of a binary conversion, so it is possible to use the binary conversion.
It works independently after installation.
The operation was checked on a Windows 11 computer.
Launching JTDX_Automatic_Operation.v0.4.0.exe will launch this GUI
Operation start JTDX monitoring begins at set timer intervals
suspension of music, dance, etc. as a sign of mourning Timer is set to 0 and monitoring stops
setting (of a computer or file, etc.) Sets the coordinates of the buttons in the JTDX window
end Script terminates


When it times out by calling another station or retrying during communication, it automatically "Clear DXAfter pressing "Transmission startPress "↑" to select "↑" and "↓".
JTDX's "Tx watchdog timer" because I think 6 minutes is too long.4 minutes-ist (used after a noun indicating someone's occupation, pursuits, disposition, etc.)5 min.and shorten it to
andCQ is forever emitted, so even though it's automatic, it still needs to be monitored.
When the Log QSO window opens, "OK" is automatically pressed and
Moving on to the next CQ as a function of JTDX
Before using the button, it is necessary to get the coordinates of the button in "Settings".
Also, if the JTDX window size is returned, the coordinates must be re-calculated in the settings.

Below is the screen that opens in "Settings".
Activate the JTDX window and then check the following items
Coordinates of the "Start Transmission" button
Take the red color during transmission and the gray color during standby
Take the coordinates for "Clear DX."
Take the coordinates of the "OK" button on the logging screen
 
April 19, 2025 　April 20, 2025